Book With Us Today!

 

 

What're your thoughts with regards to Installing A Bathtub?

Setting up a bathtub isn't exactly brain surgery, yet it does need solid plumbing, carpentry, and also often, tiling abilities. Replacing an old bathtub with a new one is also a reasonably hard project. If the old bathtub is easily available, the project can relocate immediately; if you have to open a wall surface to eliminate the old tub and also position the brand-new tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub and set in the brand-new one. Ensure you have actually qualified yourself for the task and fit attempting it. Instead of hiring a service provider to take over a halfway-completed task, it is better to think about employing one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This write-up will aid you install a brand-new bathtub in your shower room if you have actually already acquired a new tub and also don't require to transform the plan of your previous water pipes.
Your tools and also material list need to comprise the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Removing Old Touches

If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you should do is detach the water system. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of getting rid of the existing faucets can be quite troublesome as a result of the limited accessibility that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will certainly come from the pipes. When the supply pipelines have actually been removed, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Before proceeding to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.

 

 

Fitting New Taps

If the tails of the new taps are plastic, then you will need a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washers are in place in between the faucet and also the sink. Safeguard the tap in place with the manufacturer provided backnut. Once the faucet is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet adapters. The previous type ought to be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Setting up the Bathtub

Using both wood boards under its feet, put the bathtub in the required placement. The wood boards are valuable in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 little points.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the tub until the level checks out level.
To install faucets, fit the bottom of the furthest adaptable tap connector to the proper supply pipe by making a compression join; after that do the same for the various other faucet.
Switch on the water as well as check all joints and also new pipework for leaks and also tighten them if required. Load the tub and additionally inspect the overflow electrical outlet and the regular electrical outlet for leaks.
Finally, deal with the bath paneling as defined in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait until the tub has actually been utilized at the very least once as this will settle it right into its last placement.

 

 

Getting ready for the Installment

Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets unit to avoid strain on the tub.
Fit the adaptable faucet connectors to the bottom of both taps making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you make use of every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should currently be ready to be fitted in its last position.

 

 

Tiling Around the Tub

In the area where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture a rigid seal, triggering the water to permeate the wall surface in between the bath and the tiling, resulting in issues with wetness and also possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your components and also installations. They are marketed in tubes and cartridges, and are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can split rather early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant glue and also cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

We had been guided to that write-up about How to Install a Bathtub through an acquaintance on a different web address. Liked our write up? Please share it. Help others find it. Many thanks for your time. Kindly pay a visit to our website back soon.

Visit Website